一、沼氣發電機組的啟動注意事項
1、 Precautions for starting biogas generator units
1、先檢查：循環水，潤滑油，氣路。
1. First check: circulating water, lubricating oil, and air circuit.
2、打開氣路開關，扭開電瓶鑰匙（打開電磁閥開關，確定轉速控制開關處于怠速狀態）按下啟動開關。
2. Turn on the gas circuit switch, turn on the battery key (turn on the solenoid valve switch, confirm that the speed control switch is in the idle state), and press the start switch.
3、沼氣發電機組啟動后，先怠速運轉，等到水溫和油溫升高，大約45度左右。將轉速開關撥至額定轉速。
3. After the biogas generator set is started, it should first idle and wait until the water and oil temperatures rise, about 45 degrees Celsius. Turn the speed switch to the rated speed.
4、沼氣發電機組按額定轉速運轉幾分鐘，合上發電機端高壓電輸出開關。機組正常發電。
4. Operate the biogas generator set at the rated speed for a few minutes and close the high-voltage output switch at the generator end. The unit generates electricity normally.
需要注意，沼氣發電機組維護：300小時，更換一次機油，每月更換空濾機油濾。長期不用要每隔一段時間啟動一次，每次運轉半小時。希望以上的介紹能給用戶帶來幫助。
It should be noted that the maintenance of the biogas generator unit: 300 hours, replace the oil once, and replace the air filter oil filter every month. If not in use for a long time, it needs to be started every other period of time, running for half an hour each time. I hope the above introduction can be helpful to users.

二、沼氣發電機組出現不能啟動的現象怎么辦？
2、 What to do if the biogas generator unit fails to start?
1、電瓶電量不足檢查電瓶充電量。
1. Check the battery charging capacity when the battery is low.
2、電瓶線及插頭松動。
2. The battery cable and plug are loose.
3、火花塞點不了火。建議更換火花塞，因為火花塞是易耗品，
3. The spark plug cannot ignite. It is recommended to replace the spark plug as it is a consumable item,
4、燃氣管道堵塞
4. Gas pipeline blockage
時間久了，阻火器那里囤積大量水，燃氣通不了。或者在北方的冬天，里面結冰了。
Over time, there is a large accumulation of water in the flame arrester, and gas cannot be supplied. Or in winter in the north, it freezes inside.
5、沼氣里甲烷成份不穩定，或者甲烷濃度不夠。
5. The methane content in biogas is unstable or the methane concentration is insufficient.
6、電壓板、調速板、執行器、速度傳感器等回路故障。檢查相應的設備及回路。
6. Circuit faults such as voltage board, speed control board, actuator, speed sensor, etc. Check the corresponding equipment and circuits.